Beautiful Bea is a girl next door with centerfold looks!
Re: Beautiful Bea is a girl next door with centerfold looks!
And I know this is an issue for many poeple include my self.
Best regards
155,159,165+,168.
Heads:
Daria, Doris, Kama, Natalia, Penny, Rebecca,
Selina, Scarlet and Viola, + (6YE 17 + 31).
viewtopic.php?f=388&t=149636
- Funwest Doll
- Manufacturer
- Posts: 498
- Joined: Fri Mar 11, 2022 5:01 am
- Contact:
Re: Beautiful Bea is a girl next door with centerfold looks!
www.funwestdoll.com
Re: Beautiful Bea is a girl next door with centerfold looks!
Also the skeleton. I dont know if all the doll makers buy from the same dealer/producer, but I had a doll from 6.. That skelton was a total disaster.
Try to read my thread: viewtopic.php?f=383&t=140661
So my advice is: when you pick the skeleton for the doll, test it careful before cast. Is it hard to move , if then correct it, maybe some grease, and if there are rust , discard it or replace parts.
Remember : there shall 10 good rewievs to replace 1 bad rewiev.
I am in for a new doll in the spring of 2023. And it is right now I am into Irontech or a WM doll . Funwest is on my radar now, it depends of the rewievs.
I have really high hopes for Funwest.
Best regards
Edit: something like this. LHP is not perfect but close. Maybe 1-1½ cm further back.
https://www.myrobotdoll.com/products/se ... asts-168cm
https://cdn.shopify.com/s/files/1/0263/ ... 1654178016
155,159,165+,168.
Heads:
Daria, Doris, Kama, Natalia, Penny, Rebecca,
Selina, Scarlet and Viola, + (6YE 17 + 31).
viewtopic.php?f=388&t=149636
- Funwest Doll
- Manufacturer
- Posts: 498
- Joined: Fri Mar 11, 2022 5:01 am
- Contact:
Re: Beautiful Bea is a girl next door with centerfold looks!
Thanks for your attention. You are right, the problems you mentioned are indeed present in many factories. This may still have a long way to go, and the design and quality control of the factory need to be continuously strengthened. I also hope that the doll can give us the best experience.mcpe wrote: ↑Tue Jun 14, 2022 7:03 am If you can get the LHP right on every doll you make, then you will be one of the top producers of doll.
Also the skeleton. I dont know if all the doll makers buy from the same dealer/producer, but I had a doll from 6.. That skelton was a total disaster.
Try to read my thread: viewtopic.php?f=383&t=140661
So my advice is: when you pick the skeleton for the doll, test it careful before cast. Is it hard to move , if then correct it, maybe some grease, and if there are rust , discard it or replace parts.
Remember : there shall 10 good rewievs to replace 1 bad rewiev.
I am in for a new doll in the spring of 2023. And it is right now I am into Irontech or a WM doll . Funwest is on my radar now, it depends of the rewievs.
I have really high hopes for Funwest.
Best regards
Edit: something like this. LHP is not perfect but close. Maybe 1-1½ cm further back.
https://www.myrobotdoll.com/products/se ... asts-168cm
https://cdn.shopify.com/s/files/1/0263/ ... 1654178016
www.funwestdoll.com
- The Doll Man
- Moderator
- Posts: 5593
- Joined: Mon Aug 09, 2021 8:21 am
- Location: € EUROPE € @ Planet Mars
- Contact:
Re: Beautiful Bea is a girl next door with centerfold looks!
Re: Beautiful Bea is a girl next door with centerfold looks!
Somthing like this And that should be the standard for every doll there is on the marked. I dont know why it is not.Funwest Doll wrote: ↑Tue Jun 14, 2022 9:58 pmThanks for your attention. You are right, the problems you mentioned are indeed present in many factories. This may still have a long way to go, and the design and quality control of the factory need to be continuously strengthened. I also hope that the doll can give us the best experience.mcpe wrote: ↑Tue Jun 14, 2022 7:03 am If you can get the LHP right on every doll you make, then you will be one of the top producers of doll.
Also the skeleton. I dont know if all the doll makers buy from the same dealer/producer, but I had a doll from 6.. That skelton was a total disaster.
Try to read my thread: viewtopic.php?f=383&t=140661
So my advice is: when you pick the skeleton for the doll, test it careful before cast. Is it hard to move , if then correct it, maybe some grease, and if there are rust , discard it or replace parts.
Remember : there shall 10 good rewievs to replace 1 bad rewiev.
I am in for a new doll in the spring of 2023. And it is right now I am into Irontech or a WM doll . Funwest is on my radar now, it depends of the rewievs.
I have really high hopes for Funwest.
Best regards
Edit: something like this. LHP is not perfect but close. Maybe 1-1½ cm further back.
https://www.myrobotdoll.com/products/se ... asts-168cm
https://cdn.shopify.com/s/files/1/0263/ ... 1654178016
155,159,165+,168.
Heads:
Daria, Doris, Kama, Natalia, Penny, Rebecca,
Selina, Scarlet and Viola, + (6YE 17 + 31).
viewtopic.php?f=388&t=149636