I own three IRT models, the 2018 168 B labeled AYUMI one (actual 170-172cm), the 2018 169 D and the 2018 168 plus. The two former were produced by SM factory, while the third one was proposed to me as being the IRT factory version of AYUMI I. AYUMI one was no more produced but IRT made a doll with more similarity to AYUMI than the A168 plus. Apparently the IRT actual 169D is still similar to the 2018 169D.
To come back to AYUMI one I recognize that this body is one of the most realistic and gracious of my collection as it was copied from AYUMI ANIME. The only detail I didn't like too much is the fact that the 2018 model was fitted with the standard SM vagina sculpt. The SM vagina sculpt is almost perfect except that the length of the vagina (total "slit" sculpt) is reduced to 6.5 centimeters while the original (AYUMI ANIME) has the 170cm tall woman average with around 10 centimeters in length. The consequence of this was that the vaginal entry was too much forward. In fact the anal entry was were the vaginal entry should have been.
Apparently, judging from pictures I have seen and my 168 plus, IRT factory corrected this unrealistic placement on their genuine factory models.
Before owning sexdolls I was not afraid to die because I knew I would be redirected directly to paradise because I committed no serious sins. However with a lot of the vaginal entries misplacement there were on my doll collection, vaginal sex from the back was only possible for me if I used the anal hole. I just turned into a sodomite for that reason as with real women I had never such an experience.So I am now afraid about the fact that when I will die I could be redirected straight to the underground furnaces. JUST JOKING OF COURSE.
So in order to increase the realism of my AYUMI one I decided to graft the face of a real 1:1 vagina copied from real women (dollpark germany) on ayumi private parts. The vagina prints I bought were made in silicone but I used ALGINATE molding to make a TPE print. I used the same TPE as AYUMI is made of (melting it on a pan but I can also use a small electric oven for that ) IN order to keep this pussy metamorphosis reversible I decided (as for now at least) not to hot weld (iron plus hot air gun) but rather use a LOCTITE SUPER-GLUE 3 FLEX. I used isopropylic alcohool to dry the excess of oil and tried not to glue too close to the entries. Of course as the picture show the anal entry is now the new vaginal entry while AYUMI as no more anal entry. However the original vaginal entry is still accessible also.
I have made already these transformations to 5 of my dolls although I have only found three pussy copies which pleased me in the DOLLPARK store collection. For a WMdoll 100cm doll I bought for my brother I used a 20 per cent retracted alginate mold.
here are some pictures of AYUMI new pussy, vagina silicone models, some TPE prints I made and some alginate molds.
- P1020607.JPG (2.61 MiB) Viewed 1103 times
- P1020608.JPG (2.36 MiB) Viewed 1103 times
- P1020601.JPG (3.17 MiB) Viewed 1103 times
- P1020602.JPG (2.56 MiB) Viewed 1103 times
- P1020603.JPG (2.52 MiB) Viewed 1103 times
- P1020604.JPG (2.76 MiB) Viewed 1103 times
- P1020605.JPG (2.09 MiB) Viewed 1103 times
- P1020606.JPG (2.28 MiB) Viewed 1103 times
- P1020609.JPG (2.53 MiB) Viewed 1103 times
- P1020610.JPG (2.33 MiB) Viewed 1103 times
