Super disappointed in oral with WM
- VeroTwilight
- Active Poster
- Posts: 77
- Joined: Tue Aug 13, 2013 10:40 am
- Location: Middle Earth
- Contact:
Re: Super disappointed in oral with WM
Then again, there are a lot of things that should be standard and aren't (those custom fingers, for example).
Yuki - 166cm minus S32 Irontech.
Re: Super disappointed in oral with WM
Re: Super disappointed in oral with WM
1. Do you need to glue back the TPE face to the skull on just the elasticity of the face is enough to keep it in place?
2. I would like that orifice to be less tight, so could you simply just cut out the end and not putting any PVC pipe in?
3. If it fixes the issue why it is not done by the manufacturer... There is surely a downside to this?
4 We don't see in the pictures the M16 connector area, how does it attach to the skull!?
Great work man!
Jael - (YL 148) viewtopic.php?f=212&t=73333
Miriame - (SM 136) viewtopic.php?f=269&t=102115
Beth - (SM 157G) viewtopic.php?f=269&t=149637
Brooke - (Starpery 148F) viewtopic.php?t=175783
***
Re: Super disappointed in oral with WM
PM’s always welcome if you prefer to stay UTR.
I was a doubter, but now totally into it!
Re: Super disappointed in oral with WM
Asked every guy when buying his first doll.editit wrote:So it’s just two small holes?
sorry. I swear I couldn't resist!
Re: Super disappointed in oral with WM
Babel99 wrote:Wow nice tip madas... few questions here.
Gday.
1. I didn't bother glueing back the face it seems to hold well. No movement from either doll as of yet.
2. I would suggest still putting in the pvc pipe but only to cover the entrance into the skull( I tested it the skull 3 times. Once without pvc piping which worked best when it comes to loss in tightness and warping of the face. But it's too hard to file down the rough edges from the hole saw so I put in a peace of pvc piping that went to the back of the skull. Tried it and worked with extra tightness. I then also modified the internal depth of the Mouth by cutting and adding in a masturbation sleeve to allow extra penetration.
3. I didn't modify the M16 threaded connector. Just a regular connector or tho my jy doll has the new skeleton which just simply attaching on with a grub screw.
As to why manufacturers havnt changed this. Probably all comes down to cost of changing the front mould to extend the area of where the throat goes into.
Iv been talking to jy doll and they are possibly considering the change. So fingers crossed.
My biggest suggestion is to make sure the pvc piping is as flash to the entrance of the inside skull as you possibly can get it. This will ensure the face stays naturally in position
1. Do you need to glue back the TPE face to the skull on just the elasticity of the face is enough to keep it in place?
2. I would like that orifice to be less tight, so could you simply just cut out the end and not putting any PVC pipe in?
3. If it fixes the issue why it is not done by the manufacturer... There is surely a downside to this?
4 We don't see in the pictures the M16 connector area, how does it attach to the skull!?
Great work man!
Re: Super disappointed in oral with WM
PM’s always welcome if you prefer to stay UTR.
I was a doubter, but now totally into it!
Re: Super disappointed in oral with WM
Where I have circled. This is blocked and moulded as 1 piece of the front section of the mould. This is the main cause of the problem with the face warping when doing oral. As you push in the throat expands and the air that is around needs to escape somewhere. Weakest point for the air to travel is the front of the face.
Re: Super disappointed in oral with WM
Re: Super disappointed in oral with WM
PM’s always welcome if you prefer to stay UTR.
I was a doubter, but now totally into it!
- avante
- Doll Mentor
- Posts: 1700
- Joined: Tue Mar 28, 2017 11:23 am
- Location: Holland - the Netherlands
- Contact:
Re: Super disappointed in oral with WM
My doll experience : WM 158D tales & pics: viewtopic.php?f=215&t=85063&start=465
Re: Super disappointed in oral with WM
Re: Super disappointed in oral with WM
It's just more efficient than 1 plus they are only small holesj35j35 wrote:Why two holes?
- timetraveler1
- Doll Visionary
- Posts: 12336
- Joined: Tue Apr 13, 2004 12:00 am
- Location: u.s.a.
- Contact:
Re: Super disappointed in oral with WM
I am currently in the process of modding my wm doll to avoid distortion in the face when in use with great success so fair. What I have done is removed the face off the head and used a hole saw to cut out the backing of the skull section so that the insert of the Mouth can freely push inside the skull. Then what I have done is drill a small air hole at the back of the skull to allow air to blow out when you push deep inside throw the mouth. So fair this has been successful in stopping the face distortion but I will be doing some more work later 2day. I can post pics on request if need be.
I had wrote about an idea i hoped the dolls manufactures would make as a option . other blow up dolls " perfect 10 " have a hole in the back of the head that leads to back side of the throat , a rubber hose is connected to the back of the head and has a two way valve in line to adjust suction , and has a rubber squeeze bulb on it (bassically a rubber hose and bulb like on a blood pressure valve . the other way you are basically face f'ing a doll . this way you control the actual sucking motion with the squeeze bulb and suction by the adjustable two way valve.