Aylen's finger repair
Aylen's finger repair
What I used:
1. Araldite Rapid Epoxy Tubes https://www.amazon.com/gp/product/B003M ... UTF8&psc=1
2. 4-Conductor house telephone outlet wire (4 copper wires inside sleeve)
3. Paper clips
4. 50% Isopropyl Alcohol
5. TPE glue
6. Cotton Swabs
7. Razor blade
8. Wire cutters
9. Pliers
10. Cordless drill
The lighters in the pic, I didn't use, I kept at backup incase I have trouble with the TPE glue.
I would say the 1st thing is to clean the area where you will be working, I used a mixture of hand soap and water with a microfiber cloth. Aylen already had small cuts and nicks on her palms so I started with the razor blade to make a hole, grabbed my wire cutter and cut a 2" section along where her palm plate is. From there you can see where the wires are broke off and the glue resin is inside the plate. Also visible is the finger wires. I used my pliers to pull the broken wires from her fingers, the TPE will put up a bit of a fight as it is stuck to the cotton/fabric material that is wrapped around the wires, it will separate though.
I grabbed the drill and a bit that was just a bit smaller than the palm plate opening. Make sure you use the proper type drill bit as I snapped 2 of the doing this. Drilling into the glue resin it will start to break up and turn to dust, it also has a weird smell to it. I worked the bit around until the majority of resin and broken wire bits were gone.
Since I was using telephone jack wire, which has 4 copper internal wires, I decided to add some extra strength just incase the copper broke down the road. I pulled one of the internal wires out and replaced it with a cut-to-length paper clip. The clip slides right into where the 4th wire that was removed. Now this will give your girl very stiff fingers however I was thinking about having her hold stuff and paperclips can support small items.
Once you get the finger wires all set you can slide them into the finger, you will have to do some adjusting as the TPE is very elastic. I did a test fit no issues
Re: Aylen's finger repair
-
- Doll Patriarch
- Posts: 4464
- Joined: Sun Sep 20, 2015 5:08 pm
- Contact:
Re: Aylen's finger repair
I'm a great fan following her on Instagram
Hoping this makes all well and hopefully even better finger movement and stability as before the repair.
Jelina and Jelena 170cm C slim body twins.
~~~~~~~~~~~~~~~~~~~~~~~~~
DL2 Fashion Studio
viewtopic.php?t=116236
~~~~~~~~~~~~~~~~~~~~~~~~~
Olinka YL170 D
viewtopic.php?t=93693
Re: Aylen's finger repair
- sophiahugeboobs
- Doll Elder
- Posts: 2030
- Joined: Mon Feb 12, 2018 11:17 am
- Location: Germany
- Contact:
Re: Aylen's finger repair
Sofia 2.0 viewtopic.php?t=148258
Sofia 1.0 viewtopic.php?t=137813&hilit=Sofia+HiD1 ... mate+Busty
Milena-HiD160BBB viewtopic.php?f=87&t=117421
Annalena-SUPERBUSTY viewtopic.php?f=224&t=112075
Introducing Sophia (YL150 O CUP) viewtopic.php?f=212&t=97965
Re: Aylen's finger repair
Re: Aylen's finger repair
https://www.amazon.com/Apoxie-Sculpt-1- ... FNATHSFHNB
p.s. I wonder if this stuff would work just as well for that particular job? I used it to do small repairs on some plastic trophies I cast last sumer and I tell ya.. after it cures its rock solid. I had mixed up a bit to much and so I just rolled the left over portion into a ball and flattened it on my work table and I had to hit it with a flat tip screw driver and hammer to break it loose!
Re: Aylen's finger repair
You didn't find the wire too thick for the fingers? I went a similar route with telephone/thermostat wire. But I removed one strand, it was quite thick. But my lady's fingers are quite slender.
Your wires will not break.
I've cut experimental TPE over the past couple months. Just testing sealing and mending techniques with test toys. with heat. (and OOOPs, homemade paste)
Best way to cut it is with very sharp scissors. I use hairdressers scissors. It works especially good with thinner areas such as with palms.
Get a nice clean cut, no jagged edges. that seals up nice.
I have to tighten a hip. I'm certain it's not broken. Thicker material there no doubt, so cutting it clean will be more challenging.
From what experienced folks say about cutting. Silicone will cut easier with a blade than TPE
Re: Aylen's finger repair
Is this stuff 2 part? have to mix? I've used epoxy putty, it was 2 part. knead 2 together, and about 10 minutes later it's fairly stiff.Zippy81 wrote:Man I'm dreading when I have to face that day or any day similar to it.. lol.. However I think you've handled it pretty well thus far! I like your choice of outfit for her as a means of "do a good job" inspiration :p Hope it all turns out good! I think if I were to go the rubber band route I would have put some cotton balls in between her fingers and on back of her elbows to create less stress focused pressure marks. But of course if I were doing it first time.. I wouldn't have thought of that XD.. hell I probably wouldn't have thought to use rubber bands either...
https://www.amazon.com/Apoxie-Sculpt-1- ... FNATHSFHNB
p.s. I wonder if this stuff would work just as well for that particular job? I used it to do small repairs on some plastic trophies I cast last sumer and I tell ya.. after it cures its rock solid. I had mixed up a bit to much and so I just rolled the left over portion into a ball and flattened it on my work table and I had to hit it with a flat tip screw driver and hammer to break it loose!
Re: Aylen's finger repair
Re: Aylen's finger repair
I did not think of this stuff. Was helping out Rainking with ideas for his lady's finger fix. I suggested construction adhesive. I've used that for different fixes. Problem is, it takes a while to harden, but is fairly tough when cured. he did try it.Zippy81 wrote:@RGC ~ Yup sure is! You just have to make sure they are equal amounts of each part that you kneed together. can smooth it out with a little warm water also if you are using it to sculpt with.
Now I wish he'd had seen this stuff. Be a quicker solution.
Now I hope it has worked out for him.
I've never had too much luck with the liquid 2 part epoxies in the tubes.
Re: Aylen's finger repair
Thanks, I couldn't take the bent curly fingers anymore. I really couldn't think of anything else that would put pressure on the cut to help seal it, rubberbands was the 1st thing I thought of. Your cottonball idea sent me to the store to get some as the wound wasn't all the way sealed and when I came home some of the rubberbands were snapped. Lol @ good job inspiration outfit, she lives in lingerie.Zippy81 wrote:Man I'm dreading when I have to face that day or any day similar to it.. lol.. However I think you've handled it pretty well thus far! I like your choice of outfit for her as a means of "do a good job" inspiration :p Hope it all turns out good! I think if I were to go the rubber band route I would have put some cotton balls in between her fingers and on back of her elbows to create less stress focused pressure marks. But of course if I were doing it first time.. I wouldn't have thought of that XD.. hell I probably wouldn't have thought to use rubber bands either...
https://www.amazon.com/Apoxie-Sculpt-1- ... FNATHSFHNB
p.s. I wonder if this stuff would work just as well for that particular job? I used it to do small repairs on some plastic trophies I cast last sumer and I tell ya.. after it cures its rock solid. I had mixed up a bit to much and so I just rolled the left over portion into a ball and flattened it on my work table and I had to hit it with a flat tip screw driver and hammer to break it loose!
Thanks! Actually the phone wire was just a mm or 2 thicker than the original wires from the factory with the cotton wrapped around them. The fingers were thick initially, I stretched them out over the length of the phone wire and they look normal. I am definitely hoping with the epoxy, phone wire w/paperclip, her fingers should be pretty solid for awhile. I need to get some very sharp scissors, I tried with a razor blade, the TPE was pretty tough. Once the wound is all sealed I am going to put a heated spoon to it.RGC_0767 wrote:Nice job!!
You didn't find the wire too thick for the fingers? I went a similar route with telephone/thermostat wire. But I removed one strand, it was quite thick. But my lady's fingers are quite slender.
Your wires will not break.
I've cut experimental TPE over the past couple months. Just testing sealing and mending techniques with test toys. with heat. (and OOOPs, homemade paste)
Best way to cut it is with very sharp scissors. I use hairdressers scissors. It works especially good with thinner areas such as with palms.
Get a nice clean cut, no jagged edges. that seals up nice.
I have to tighten a hip. I'm certain it's not broken. Thicker material there no doubt, so cutting it clean will be more challenging.
From what experienced folks say about cutting. Silicone will cut easier with a blade than TPE
Re: Aylen's finger repair
Re: Aylen's finger repair
I'm sure a lot depends on usage, but for a new user would be better suited for no bones in the fingers? This seems like a very doable repair, but I'm not sure if I'd want to perform this every 3 months. Thanks for any guidance, Jason.
Re: Aylen's finger repair
Thanks Jason, I wouldn't think that this is something that would be needed often. The main thing for me is to use materials that would hold up longer than the factory setup, one of the reasons I went with the paperclip inserts, those are pretty ddurable. I did some research in a few threads of hand repair and decided to give it a try. I am hoping to not have to do this again for quite some time. If for some reason my technique doesn't last, I will fasten/attach something to the palm plate.gamille wrote:That's a very nice, detailed write-up. I just joined here and researching a future doll purchase. It seems from posts here, that fingers are quite the issue. I certainly don't want to jack a valuable thread, but how frequent are hand repairs needed?
I'm sure a lot depends on usage, but for a new user would be better suited for no bones in the fingers? This seems like a very doable repair, but I'm not sure if I'd want to perform this every 3 months. Thanks for any guidance, Jason.