That horrible BJ face GONE

Maddas · Post by **Maddas** » Sat Mar 17, 2018 2:20 am

So here we go. Finished the mod with great success.
Tested and fully working without any face distortion.

I originally did this to gain extra penetration when using her but much to my surprise it stopped the horrible face distortion and eyes popping out.
Attached are pictures.

1st. Remove the face(it's pretty easy)
2nd. Grab a circular hole drill bit and drill out the backing of the throat (I suggest wearing a face mask to avoid breathing in the fibers)
3rd. Drill a couple of holes at the back of the skull to allow air flow(this is to allow air to escape when penetrating
4. Attach some pvc piping and glue it inside the skull(this is to help keep the tightness around your little/big 1)
5 Re attach the face and away you go

On a side note. I also modded the inner mouth to accept my downstairs by cutting the end off and attaching a larger masturbation sleeve and glueing it in.

Now you can go nuts without worrying or catching a glimpse of that horrible face we all know about when you go too fast and deep.

Iv done this to both my WM 156cm and JY 170cm.

Now go out there and go balls deep. Lol

The Doll Laboratory · Post by **The Doll Laboratory** » Sat Mar 17, 2018 2:45 am

Hello Maddas,

Interesting, thanks for sharing.

Could you, for scientific purpose of course

, take some photos of your modified head with a dildo (or similar object) inserted in her mouth?

Von Rubber

Maddas · Post by **Maddas** » Sat Mar 17, 2018 3:04 am

VonRubber wrote:Hello Maddas,

Interesting, thanks for sharing.

Could you, for scientific purpose of course , take some photos of your modified head with a dildo (or similar object) inserted in her mouth?

Von Rubber

Hi Von.
Attached are pictures of a glass rolling pin inserted 7inches into the mouth.

Picture is my JY170

The Doll Laboratory · Post by **The Doll Laboratory** » Sat Mar 17, 2018 5:10 am

Hello Maddas,

Thank you.

It seems to work. There is still some deformation (nose) but it’s way better than before.

Von Rubber

Maddas · Post by **Maddas** » Sat Mar 17, 2018 5:29 am

Hi Von.

Yes there is a slight push up to the nose but I believe there is absolutely no way to stop that due to the nature of tpe and how the faces are developed.
But compared to eyes popping of their sockets. Its much better.
On the other hand if the manufacturers changed the direction if the throat to be more natural rather than upwards and actually sectioned the throat instead of sharing the same cavity for both the throat,eyes and cheeks. This would dramatically help reduce the distortion. Also. What helps the distortion most is the fact of having blow holes at either the base or back of the head

Unknown03 · Post by **Unknown03** » Sat Mar 17, 2018 8:50 am

Maddas wrote:What helps the distortion most is the fact of having blow holes at either the base or back of the head

I was tempted but won't make a pun here.

Impressive work!

Mr Miyagi · Post by **Mr Miyagi** » Sat Mar 17, 2018 8:56 am

blow holes to fix the blow hole.

089 · Post by **089** » Sat Mar 17, 2018 2:22 pm

Thank You, OP!

Seeing the face distortion (in a manufacturer video) made me cringe. Talk about NOT sexy.

Your mod puts oral back on the table.

Post by **Akiko Kurosawa** » Sat Mar 17, 2018 3:06 pm

Impressive but do you have cure for RBF...

Resting Bitch Face?

Maddas · Post by **Maddas** » Sat Mar 17, 2018 4:58 pm

Akiko Kurosawa wrote:Impressive but do you have cure for RBF...

Resting Bitch Face?

Rbf?
Sorry I'm unfamiliar as iv only had my dolls for a couple of months and new to it all.
Can you provide a picture

Unknown03 · Post by **Unknown03** » Sat Mar 17, 2018 6:18 pm

doll-noob55 wrote:blow holes to fix the blow hole.

Yes, that was quite an impressive blow job.

Sorry, just couldn't resist any longer!

Maddas · Post by **Maddas** » Sat Mar 17, 2018 9:14 pm

Haha. I knew as soon as it was posted it would be used lol. All good.
Im wanting to do the same mod on another head and doll but in more detail by putting a plastic backing plate around the face and actually sectioning the throat in a more natural way and by going 1 step further and piping the throat down 2wards the neck to allow more positions when in use. I have all the tools and equipment needed but no doll. If only money grew on trees.

Strider · Post by **Strider** » Sat Jul 07, 2018 10:19 am

Thanks for this, Maddas. I'll be attempting a mod inspired by this soon, l hope.
I have a couple questions.
1. What glue did you use to attach the picture to the skull?
2. What glue would one use to attach the skin back to the skull? My doll's face/head skin is kinda loose.

Strider · Post by **Strider** » Mon Jul 16, 2018 10:45 pm

oops.

1. What glue did you use to attach the pvc pipe to the skull?

Maddas · Post by **Maddas** » Tue Jul 17, 2018 4:11 pm

For the skin I didn't use any glue. I just put the face back on. For the pipe I used water proof silicone(make sure you allow it to cure. This is incase of repairs. So fair I havnt had any issues

The Doll Forum