Scrap Metal Ball Bearing Wrist and Palm plate
Scrap Metal Ball Bearing Wrist and Palm plate
Was just bored and dreamed up this for your doll. Anyone can tweak this and make it work for their doll. It will definitely work. Not sure how easy it would come loose. It is scrap metal after all LOL
It's not finished, but concept is all there.
Have Fun.
- von_Shredhead
- Doll Guru
- Posts: 5561
- Joined: Tue Mar 06, 2012 7:34 pm
- Location: Third Rock From The Sun
- Contact:
Re: Scrap Metal Ball Bearing Wrist and Palm plate
Nina's Thread - Doll Sweet 145cm
Lila's Thread - Doll Sweet 145cm
Heather's Thread - 4Woods Allure
Sativa's Thread - Virgin Rose Kelu
Naomi's Thread - 1AM WM125
"Build a man a fire, and he'll be warm for a day. Set a man on fire, and he'll be warm for the rest of his life."
- Anung Un Rama
- Doll Visionary
- Posts: 14846
- Joined: Fri Oct 31, 2014 2:27 am
- Location: The Dollsmith..hanging out with the Un Rama band on the Central Coast Of Oz! Life is gigs and jams!
- Contact:
Re: Scrap Metal Ball Bearing Wrist and Palm plate
into either a 5 port pneumatic terminal block or plate (mill and drill 101)
or prefab PTFE - Teflon (needs to this compound due to higher melting point than tpe injection temp) electrical terminal block
and the ball is now rolling.
Anung
THE UN RAMA'S
Lilith Un Rama - RD She Devil Custom Bod 10 (DOLLMILF and TDF Doll Queen)
Natasha-RD Classic - Bod 6
Lexi-BT 3 (C) Star Bod 3 Gel butt & boob implants
Lorelei-SANHUI 165R cup my custom elf head 007
Emerald-R13 custom
Tammy-PIB IG -Bella Head
Ayla-WM dolls - 155cm DD cup model
Jessica Jade-PD - 163cm, Penelope fitness version .
Mazzy M-JY/AS Doll 166cm fitness model
Pearl-JY150cm Fantasy Fitness my design
BaBs-PD 158cm Mega Boobs doll
Jessie-TB Deluxe-Jessica Model
Danny-YL Dolls-128cm Kylie model
Gypsy Kate-WM 140cm D cup head #36
Dommy-SANHUI 65cm Mini silicone doll
Mini Dolls lots!
My designs: PD 160 cm FBB Motoko Kusinagi GITS, She Demon Agony & 150cm Fantasy fitness Pearl
Re: Scrap Metal Ball Bearing Wrist and Palm plate
There are plastic pellets Polymorph. put in boiling water it softens to a gel, then shape to whatever you wish. could wedge the ball wired fingers in that.Anung Un Rama wrote:And...I likey ...and I add in here are your finger wire inserts.... (shankball each end)
into either a 5 port pneumatic terminal block or plate (mill and drill 101)
or prefab PTFE - Teflon (needs to this compound due to higher melting point than tpe injection temp) electrical terminal block
and the ball is now rolling.
Anung
The thicker the polymorph is, stronger it is. No 3d printer needed. Polymorph plastic can be reheated and worked with again. Do not think it adheres to metal too well though. It's cool stuff anyway. For a joke I may make a set of eyes... LOL
I tried to drill and tap the ball to put a threaded bolt in. I'd busted all my small drill bits on previous jobs, so pilot hole I was not able to do. Have to get more. So just flared end of brake tube and welded it on ball. Not the best. Just experimenting. Giving others the ideas and passing them along.
For WM could put a smaller tube on this and insert into existing arm, fasten with a self tapping screw.
For the wired wrist type, put tube with a nut on end, screw on to forearm.
Pure concepts.
Re: Scrap Metal Ball Bearing Wrist and Palm plate
When puttering with this idea, mostly was thinking replacement.
As an experiment, just got some of the polymorph into a gel in two pieces and placed old wires between and sandwiched wires between them
Once hardened, I cannot pull them out without using brute force If made to proper size for a palm plate, this would work good to hold any sort of wire replacement. Use a small screw or crimp plate over it. Polymorph would melt during molding for sure. Boiling water is all it takes to gel this stuff.
More low cost solutions anyway. Got the polymorph stuff from Ebay:
https://www.ebay.ca/itm/DIY-50g-100g-4m ... 2749.l2649