Filling boobs with water
-
- Active Member
- Posts: 107
- Joined: Mon Jul 03, 2017 4:31 am
- Location: Location, Location
- Contact:
Filling boobs with water
I'm thinking of it, but afraid of my bed ending up like a scene from the Poseidon Adventure.
There really has to be a morning after for me.
Are they usually pretty leak proof and watertight ?
- infl8orama
- Senior Member
- Posts: 278
- Joined: Tue Sep 02, 2003 12:00 am
- Contact:
Re: Filling boobs with water
It should go without saying, but just in case: Do NOT fill Milk Maid's breasts up with anything but water. On at least one version, her nipples are primitive bite valves, so while you can suckle, it will take a long time to get a preponderance of the milk out, and the remainder will curdle and grow lots of microbes. I don't have personal experience with this issue, but given how difficult it is to get any water out of a doll's breasts through the valve, I can only imagine the science experiment you'd wind up with using any kind of food liquid.
— H.L. Mencken
-
- Active Member
- Posts: 107
- Joined: Mon Jul 03, 2017 4:31 am
- Location: Location, Location
- Contact:
Re: Filling boobs with water
Thanks for the advice.infl8orama wrote:I've had Pussy Galore, Milk Maid, and a couple other water-breasted dolls over the years, and usually the breasts (which are separately chambered) are quite resilient. Getting the water out can be a challenge.
It should go without saying, but just in case: Do NOT fill Milk Maid's breasts up with anything but water. On at least one version, her nipples are primitive bite valves, so while you can suckle, it will take a long time to get a preponderance of the milk out, and the remainder will curdle and grow lots of microbes. I don't have personal experience with this issue, but given how difficult it is to get any water out of a doll's breasts through the valve, I can only imagine the science experiment you'd wind up with using any kind of food liquid.
The reason I'm asking is that on one of the boobs, I stupidly opened the valve to see if I could add more air.
They felt a little soft as shipped.
Now I'm finding it near impossible to add more air as the second I remove the valve, half the air escapes.
They are not safety, air valves, but meant for water I'm guessing ?
- infl8orama
- Senior Member
- Posts: 278
- Joined: Tue Sep 02, 2003 12:00 am
- Contact:
Re: Filling boobs with water
— H.L. Mencken
- ILuvFemsNlingerie
- Doll Elder
- Posts: 2556
- Joined: Wed Dec 17, 2008 12:00 am
- Location: Louisiana
- Contact:
Re: Filling boobs with water
It's kinda a pain because you have to put in a little at a time and use the eraser end of a pencil or something long and blunt to stuff the fiber fill in. I don't know how much I'll need to fill up both breast but where I stopped the FF ended up looking tubed shaped.
-
- Active Member
- Posts: 107
- Joined: Mon Jul 03, 2017 4:31 am
- Location: Location, Location
- Contact:
Re: Filling boobs with water
I'll fill them with water tonight.
Giving her a little more weight should be a good thing too and add to the realism.
Hope she'll still stand up though!
-
- Active Member
- Posts: 107
- Joined: Mon Jul 03, 2017 4:31 am
- Location: Location, Location
- Contact:
Re: Filling boobs with water
ILuvFemsNlingerie wrote:My 1am Buffy I was able to get air in her boobs but it was difficult. I have a similar one that I got from Samara78 and it was impossible to put air in it so I started putting fiber fill which I haven't finished doing yet.
It's kinda a pain because you have to put in a little at a time and use the eraser end of a pencil or something long and blunt to stuff the fiber fill in. I don't know how much I'll need to fill up both breast but where I stopped the FF ended up looking tubed shaped.
Yes, a pain trying to inflate them with air.
I'll have to give water a go.
I have a small plastic funnel somewhere that should make it easy.
- paula_dam
- Contributing Poster
- Posts: 47
- Joined: Tue Aug 26, 2003 12:00 am
- Location: Buenos Aires
- Contact:
Re: Filling boobs with water
I always poured a couple of cups of warm water in the tube, removed all excess air, closed the valve and then inflated the doll.
Best plastic titjob I've ever had!
Re: Filling boobs with water
That is crafty!paula_dam wrote:I've had Pussy Galore. Her breasts were made from a unique piece of a very soft rubber. Not really big, but some of the best tits I remember on a doll!
I always poured a couple of cups of warm water in the tube, removed all excess air, closed the valve and then inflated the doll.
Best plastic titjob I've ever had!
*My juicy Cherry: viewtopic.php?t=154759
*Z-cup Moira: viewtopic.php?t=138543
*BBW Breanna: viewtopic.php?t=143116
*Yulia: viewtopic.php?t=122950
*Tina viewtopic.php?t=121819
*Aurora Jolie: viewtopic.php?t=106838
*World-famous Una Carha: viewtopic.php?t=93292
Re: Filling boobs with water
Maybe it's me - had air babes past and present with this feature
Just never bothered with it found the air inside the boobies enough for me -
The whole new idea of a more complex clean - up - and finding away to get the water out
Air - On -
Re: Filling boobs with water
- DoctorDuke
- Doll Mentor
- Posts: 1378
- Joined: Mon Apr 28, 2008 12:00 am
- Contact:
Re: Filling boobs with water
Re: Filling boobs with water
- DollLoverDude
- Active Member
- Posts: 162
- Joined: Fri Sep 02, 2016 6:15 am
- Contact:
Re: Filling boobs with water
I was thinking about using regular balloons for this (maybe a somewhat larger size, though): you insert the empty balloon into the inflatable breast, then fill up the balloon with water, then either tie a knot into the balloon, or try to shut it with the valve itself.
Main advantage would be that no water gets directly into the inflatable, and a secondary advantage might be that the boob might become somewhat more 'squeezable'...
Haven't tried it yet, but seems to be feasible!
-
- Active Member
- Posts: 181
- Joined: Fri Aug 30, 2013 10:15 pm
- Contact:
Re: Filling boobs with water
Random question here, but what is that figure in your profile gif, @DollLoverDude?DollLoverDude wrote: ↑Thu Jun 01, 2023 4:35 pm I was thinking about that as well lately! My Evie doll would be the ideal candidate for that I'd imagine...
I was thinking about using regular balloons for this (maybe a somewhat larger size, though): you insert the empty balloon into the inflatable breast, then fill up the balloon with water, then either tie a knot into the balloon, or try to shut it with the valve itself.
Main advantage would be that no water gets directly into the inflatable, and a secondary advantage might be that the boob might become somewhat more 'squeezable'...
Haven't tried it yet, but seems to be feasible!