Joining the sanhui ranks

Arthur1960 · Post by **Arthur1960** » Wed Aug 07, 2019 7:56 am

Hi and congratulations on Shione's safe arrival today! She looks great and whenever I see pics of these Sanhui gals I begin to think that maybe it's time to let a silicone lady into the harem! As for the loose head, I would imagine that the push fit bolt is similar to the new Jinsan bolt in which case I find 1 or 2 rubber O ring washers do the trick. Alternatively some use felt washers, in any event something like that should stop Shione going the full exorcist on you! Look forward to your forthcoming pics!

Pabzilla · Post by **Pabzilla** » Wed Aug 07, 2019 8:05 am

I thinks so, I can't push it any farther down, although its very easy to pull off again should it be like that?
Is there a technique to fitting it or just push?

Pabzilla · Post by **Pabzilla** » Wed Aug 07, 2019 8:17 am

Thanks Arthur, I will give washers a go, I was thinking maybe the notch in the head bolt might need adjusting to make it sit more proud, looks to me like a hex key would adjust it is that right?

: IMG_20190807_131242.jpg (197.96 KiB) Viewed 1649 times

: IMG_20190807_131212.jpg (227.09 KiB) Viewed 1649 times

: IMG_20190807_131321.jpg (180.34 KiB) Viewed 1649 times

Sorry about the pic quality

Arthur1960 · Post by **Arthur1960** » Wed Aug 07, 2019 8:41 am

Hi again, yes those are little grub screws that can be adjusted to allow for a tighter fit. Looks like the same sort of bolt that Jinsan now use. After experimenting I found that the best fit was obtained for my dolls by screwing the threaded portion into the neck and having the push fit end go into the head but of course your gal could well have a different arrangement with no threads in the neck tube. If it is threaded you could try it that way around although if the bolt is firmly in the head then probably best to try and adjust those grub screws and fit a washer. Also the neck bolt could be a double push fit in which case forget what I said about screwing into the neck first!

Pabzilla · Post by **Pabzilla** » Wed Aug 07, 2019 8:44 am

Thanks again Arthur, this forum is essential for newbies like me to pick you guys brains.
Thanks buddy

Pabzilla · Post by **Pabzilla** » Wed Aug 07, 2019 7:35 pm

Have just tried Arthur's solution to Shione's spinning head and the washer has cured the problem, I'm delighted with my lady.
Thanks Arthur.
And thank you also Sofos for offering advice.

WaffleAnomaly · Post by **WaffleAnomaly** » Wed Aug 07, 2019 7:40 pm

Congrats on your Sanhui! Don't throw your back out having too much fun at once

Pabzilla · Post by **Pabzilla** » Wed Aug 07, 2019 7:45 pm

Ha ha... thank you WaffleAnomaly, its going to be hard to resist her.

Maviarab · Post by **Maviarab** » Wed Aug 07, 2019 7:48 pm

Catching up...grats Pab...glad she arrived safely. Any advice needed regarding silicone let me know

gonestill77 · Post by **gonestill77** » Wed Aug 07, 2019 7:55 pm

Congrats man!

Glad she got to you ok.
She's a beauty.
Have fun.....

Pabzilla · Post by **Pabzilla** » Wed Aug 07, 2019 7:57 pm

Thank you Mavi, its great the waiting is over coz its just an endless worry.
Will she be damaged?
Did I order the right doll and options?
Will she break my back?
Will I miss the delivery?

And it all worked out fine, I'm very happy buddy.

Pabzilla · Post by **Pabzilla** » Wed Aug 07, 2019 8:01 pm

Thanks Gonestill, your an ambassador for sanhui and your Eve looking so great after 3 years is one of the big reasons I went Sanhui. Thank you.

gonestill77 · Post by **gonestill77** » Wed Aug 07, 2019 9:59 pm

Pabzilla wrote:Thanks Gonestill, your an ambassador for sanhui and your Eve looking so great after 3 years is one of the big reasons I went Sanhui. Thank you.

Your welcome!

No problem.....