Options to "fill out" old RD B9 Breasts
Moderator: TJ_Foxx
-
- Active Member
- Posts: 181
- Joined: Fri Aug 30, 2013 10:15 pm
- Contact:
Options to "fill out" old RD B9 Breasts
As you can see from the pic below, the breasts have (as expected) sagged a lot over the last 10 years this doll has been around:
I'm not under any delusions that she can be restored to near her original state, but I'd like to improve her a bit if possible.
My question is what sort of options are there to "fill out" her breasts?
I've tried looking through old posts on the board but most of the info around breast restoration involves newer TPE dolls or work to repair serious tears and separation of the breasts.
Any help or suggestions would be appreciated.
Thanks!
Re: Options to "fill out" old RD B9 Breasts
I would definitely PM Dodgeman and get his opinion. Here is mine, its a Tin cure so its literally curing itself to death. Those saggy boobs will eventually just fall off, you can slow the droop if you support the breasts in a good brau when not in use. This might slow that process down, but it will not stop it. I know of no process that will bring the saggy boobs back...SuckItTrebek wrote:So, I'm picking up an old tin cured B9 RD from cnd2008 next week.
As you can see from the pic below, the breasts have (as expected) sagged a lot over the last 10 years this doll has been around:
I'm not under any delusions that she can be restored to near her original state, but I'd like to improve her a bit if possible.
My question is what sort of options are there to "fill out" her breasts?
I've tried looking through old posts on the board but most of the info around breast restoration involves newer TPE dolls or work to repair serious tears and separation of the breasts.
Any help or suggestions would be appreciated.
Thanks!
Re: Options to "fill out" old RD B9 Breasts
When she's at rest bend her arms at the elbows 90 degrees so the inner arms support her breasts. This will keep them from hanging to the sides and stretching.
Best of luck to you! It's nice to see one of the legendary Body 9's again. This must be the way classic car enthusiasts feel!
*My juicy Cherry: viewtopic.php?t=154759
*Z-cup Moira: viewtopic.php?t=138543
*BBW Breanna: viewtopic.php?t=143116
*Yulia: viewtopic.php?t=122950
*Tina viewtopic.php?t=121819
*Aurora Jolie: viewtopic.php?t=106838
*World-famous Una Carha: viewtopic.php?t=93292
-
- Active Member
- Posts: 181
- Joined: Fri Aug 30, 2013 10:15 pm
- Contact:
Re: Options to "fill out" old RD B9 Breasts
Yup, I know she's on borrowed time and in essence, fading away like Thanos snapping his fingers.Zebo wrote: I would definitely PM Dodgeman and get his opinion. Here is mine, its a Tin cure so its literally curing itself to death. Those saggy boobs will eventually just fall off, you can slow the droop if you support the breasts in a good brau when not in use. This might slow that process down, but it will not stop it. I know of no process that will bring the saggy boobs back...
More or less, I'm just trying to see if I can get her to stick around for a few months or so until I decide on a better option.
I don't expect there to be a way to reduce the saggyness of the boobs as much as just hoping there was a way to fill them out bit before she runs her course, or the boobs just fall off.
-
- Active Member
- Posts: 181
- Joined: Fri Aug 30, 2013 10:15 pm
- Contact:
Re: Options to "fill out" old RD B9 Breasts
Good suggestions.CF wrote:If the breasts are hollow, you can inflate them with air using a needle and whatever kind of pump (electric or manual) you have handy. If you go the electric route, work slowly so you don't over-inflate.
When she's at rest bend her arms at the elbows 90 degrees so the inner arms support her breasts. This will keep them from hanging to the sides and stretching.
Best of luck to you! It's nice to see one of the legendary Body 9's again. This must be the way classic car enthusiasts feel!
I'm no expert on this but I believe the RD boobs, include the B9, are solid.
So temporary air filling is a no go.
-
- Contributing Poster
- Posts: 33
- Joined: Fri Jun 15, 2018 8:17 am
- Contact:
Re: Options to "fill out" old RD B9 Breasts
- sam treadwell
- Doll Advisor
- Posts: 811
- Joined: Fri Jun 24, 2011 1:59 pm
- Location: Anaheim
- Contact:
Re: Options to "fill out" old RD B9 Breasts
I think so too, SIT. I have an older body D, and they feel pretty solid to me. Although it feels like it’s possible that there is a small, hollow portion at the center.SuckItTrebek wrote:I'm no expert on this but I believe the RD boobs, include the B9, are solid.
I second Brick’s suggestion on the support bra, as that’s probably your best bet to further preserving her breasts at this point.
I recently came across a thread in which a member had to replace the breasts on his older RealDoll. He used a Ruby 13 breast pillow as the donor. He pieced it in rather well, and it actually came out looking pretty darn good. I mention this as an option, should it ever come down to this. Though hopefully it won’t.
Sam
- HotDiggityDoll
- Doll Elder
- Posts: 2581
- Joined: Mon Jun 13, 2005 12:00 am
- Contact:
Re: Options to "fill out" old RD B9 Breasts
It's 2 part, Abyss can set you up with it.
Those were probably quite pendulous from day 1 however.
Re: Options to "fill out" old RD B9 Breasts
The Breast are solid, so no air is going to pump them up.
Also, the kits Abyss provides is for Platinum cure silicone. I don't think you can mix those 2 types of silicone, and I know Abyss does not carry any tin cure in stock.
- sam treadwell
- Doll Advisor
- Posts: 811
- Joined: Fri Jun 24, 2011 1:59 pm
- Location: Anaheim
- Contact:
Re: Options to "fill out" old RD B9 Breasts
https://www.smooth-on.com/category/tin-silicone/
https://www.amazon.com/Smooth-OOMOO-30- ... dpSrc=srch
-
- Active Member
- Posts: 181
- Joined: Fri Aug 30, 2013 10:15 pm
- Contact:
Re: Options to "fill out" old RD B9 Breasts
I'm not sure I'm going to invest too much time/money into the doll. I'll have a better idea once I get my hands on her next week.
If I think its worth the time I might take a dive and look into the Smooth-On solution.
-
- Active Member
- Posts: 181
- Joined: Fri Aug 30, 2013 10:15 pm
- Contact:
Re: Options to "fill out" old RD B9 Breasts
Like I mentioned before, I'm not looking to bring her back to her former glory, but more to fill out her breasts a bit to compensate for the sag. I know this will increase weight too, so that's also a concern/limitation.
Would these be spot injections or something inserted through the nipple? Really searching in the dark here for "education" on this sort of thing.
- HotDiggityDoll
- Doll Elder
- Posts: 2581
- Joined: Mon Jun 13, 2005 12:00 am
- Contact:
Re: Options to "fill out" old RD B9 Breasts
Mix the 2 parts and inject right away! I thought I was smart at one point and waited for it to set up a bit so it would not try to ooze back out so bad, and it quickly became impossible to inject.
You inset the needle through the nipple and work it in and out a few times to sort of create space in there then inject. Because you are not injecting into empty space, it's a solid that shrank, there is no void in there.
When I did my BoyToy doll I went through the breast walls, that was a mistake, I got instant 'bubble' pocket rise to the surface of the breast, creating a lump. Not a good look, I was then forced to do more spot injections around the lump to even it all out. It took a lot of time and injections. And left little miscolored spots, freckles on her breasts. Although eventually I got it looking half decent.
When my Realdoll started to deflate a bit I still had leftover Gel in the fridge so I gave her a few injections. I followed the most recommended method and went though the nipples. Much better results!
You want to have a method ready to apply pressure around the needle to stop oozing back out. I found a great method was to inject and leave the needle in! Wrap a rag around the needle and had elastic bandage wrapped around her to hold the rag in place and the needle upright. Come back every few minutes and push the plunger down again (the pressure in the breast pushes back, if you pull the needle out most will ooze out, leave the needle in and it goes back into needle, so push it back in every few minutes and each time a little more stays in the breast as it cures.
You go with the needle through the nipple and as deep as you can into the breast rather than aim for the depressed saggy spot, otherwise if you shoot right into the sag you can end up with a bubble near the breast wall. Be ready to wrap the breast with elastic bandage to a round shape, if a bubble does appear this will reduce it.
If you keep injecting and not making much fifference to the sag then try aiming a little more in that direction.
I wonder how much you intent to inject and how deep! Those breasts are huge!
Samara cut nipples off and injected, that may work better for huge pendulous boobs?
- HotDiggityDoll
- Doll Elder
- Posts: 2581
- Joined: Mon Jun 13, 2005 12:00 am
- Contact:
Re: Options to "fill out" old RD B9 Breasts
Re: Options to "fill out" old RD B9 Breasts
Fallon - JY-166 muscle doll
Arrived (YL 170 thread) - YL-170
TBD - YL-170 (2nd attempt)
Devoted customer of Booty Call Dolls