The Doll Forum

Mystere wrote:Hi samara,

I've had my TPE WM158 doll for two months now and she's still in great shape. But could you lend your advice on a few repair issues?

I think she has developed a small tear at the bottom of her labia (see attached photos). What is the best way to fix this, and how could I have prevented it?

Whenever I apply vaseline to her vagina with my fingers, I feel a few "rough areas." I don't know how else to describe it and it's very difficult to see them. But it feels like small areas where the textures have become rough or perhaps there are tiny bits of TPE hanging loose. I don't notice any discomfort when I have sex with her, but I'm concerned. Again, what is the best way to fix this, and how could I have prevented it?

Yes, I too am having this same issue with my OR138. I have tried "glue" but to no avail. It does not seem to be getting worse but it does worry me a bit.

If it isn't getting worse i would not worry too much.
Petroleum jelly in there once in a while will kind of waterproof her a little, and help hold in the proper oil content. Repeated washing means you wash some of the oil that needs to be there out of the doll. You have to keep that entry fresh or it will deteriorate over time from being "high traffic" down there.

Anyone out there have loose knee joints in their WM doll?

If so have you tighten them up and how did you do it?

Thanks

Can anyone help Cee Cee?

ILuvFemsNlingerie wrote:Anyone out there have loose knee joints in their WM doll?

If so have you tighten them up and how did you do it?

Thanks

These are welded immobile. You would have to make a clean cut along the seam on both sides of the knee where the bolts are located. Cut at the seam. Have two socket wrenches and sockets and try to tighten her up like that.

Samara,
A 170 Z one.
Could you repair this w/o moving her form the box?
Love,
Nyoko

Booty Call Dolls wrote:Samara,
A 170 Z one.
Could you repair this w/o moving her form the box?
Love,
Nyoko

How did that happen? a machette?

Nope

Yeah I saw a response in another thread about the joints being welded and was bummed to find that out. Oh well she's fine the say she is the next doll will hopefully be easier to fix if that happens again.

This is delamination. Send her over for a seamless repair Jeff. I will gladly do it for you. You will need to wrap her breast in seran and pack her in with pressure everywhere except on the breast area give her a seran over the shoulder boulder holder. Pack her for a bomb blast. Just send the body unless you need makeup work.

The owner needs to repair the open area where the gel is first. Use acetone to clean from the bottom up.especially the lip where the gel is the imale part on the chest. And the whole area under the gel part both peices. Now to apply adhesive (sil poxy is the best don't skip) use a wooden tongue depressor to spread a thin layer of adhesive. Do it in small sections.

Any tips on how to remove eyelashes?
Love,
Nyoko

Booty Call Dolls wrote:Any tips on how to remove eyelashes?
Love,
Nyoko

Tpe or silicone darlin?
For silicone carefully with tweezers.
For tpe treatment use baby oil massage on the eyelids and it will break down the super glue they use to apply them. Use a touch isopropyl 70% at first on a cotton tip

Hi Samara,

am about to receive a TPE DH168 150cm,

and, i am wondering what the temperature limits for picking a safe storage area are.
I have some closets that do heat up a bit as the summer sun's heat moves through the roof.
So, i was wondering what the safe range for hot, and cold, would be.

Thank you very much.

@ IWI:

Jeff pointed me to your question.

A temperature of 40-50 °C / 100-120 °F is not harming a TPE doll.
Direct sunshine (UV radiation) is not good for the TPE doll.
Therefore, the TPE doll should not be stored where the sunlight enters through a window.

For storage, the TPE doll should be stored flat and not sitting in a chair.
There are two methods for this:

1.) The blanked method:
The transport carton of the TPE doll is very well suited for this purpose.
A blanket is folded and placed at the end of the head in the cardboard box.
A second blanket is folded and placed in the box at the foot end.
This results in a gap in the area of the buttocks, the so-called "buttocks gap", so that the buttocks are not flattened during prolonged storage.
A third blanket is now placed in the carton on the folded blankets.
Then the TPE doll is laid and the blanket is then folded over the TPE doll.
Because of the air circulation the carton should not be closed with tape.

2.) The mattress method (recommended for longer storage):
In this case, a foam mattress is taken and the foam is cut out exactly where the buttocks are located.
Then a blanket is placed on the mattress.
Then the TPE doll is placed and the buttocks fit exactly in this cutout.
Then the blanket is folded over the doll.


Cold is not a problem.
You are not able to freeze TPE.
At that temperature it is more a problem for the metall skeleton.
The worst you can do is a wet and cold cellar.


If the storage is only 1 to 2 days, the TPE doll must not be cleaned beforehand.
If storage takes longer, the following applies:
The wig is removed.
Clothing is pulled out as this could cause pressure points.
The TPE doll is washed, dried, oiled and finally powdered.
All openings must be absolutely dry.