Elsa Babe 160cm L-cup REVIEW
- just a guy
- Doll Mentor
- Posts: 1040
- Joined: Tue Apr 25, 2023 3:36 pm
- Location: Finland
- Contact:
Re: Elsa Babe 160cm L-cup REVIEW
I first put the epox to the screw and the wrench socket. Let it sit 10 minutes. Seems the epox is super tough. the socket stayed there so then I put epoxt around the wrench socket and then lift the upper body and put the metal pipe on to the socket so the soket is now inside the back bone pipe. Socket was only 2,1 cm wide so there's more room than the other socket I had which is 2,5cm. Since the socket I bought has lenght like 6-8 cm it was very hard to lift the body since I had to stretch it so much. This is why I also bought leghty socket so if / when the back bone pipe comes off it doesn't just fall of like that.
I now let the thing sit 10 minutes and then try to lift the upper body. If the body sit's nicely I then wash the back since it's very dirty now and then sealed it with silicone glue. I had accidentally cutted the back too low when I first made the opening cut to the back and had to glue it together. Silicone glue has done it's job greatly and the scar is almost invisible so I know that the current opening can be sealed nicely too
Review of my Monica Hentai Torso Doll - viewtopic.php?t=169345
Review of my Elsa Babe 160cm L-cup - viewtopic.php?t=172708
Best way to clean a doll
Best way to dry a doll
Where to buy doll clothes
After honeymoon
- just a guy
- Doll Mentor
- Posts: 1040
- Joined: Tue Apr 25, 2023 3:36 pm
- Location: Finland
- Contact:
Re: Elsa Babe 160cm L-cup REVIEW
Here's the epox I used
Review of my Monica Hentai Torso Doll - viewtopic.php?t=169345
Review of my Elsa Babe 160cm L-cup - viewtopic.php?t=172708
Best way to clean a doll
Best way to dry a doll
Where to buy doll clothes
After honeymoon
- just a guy
- Doll Mentor
- Posts: 1040
- Joined: Tue Apr 25, 2023 3:36 pm
- Location: Finland
- Contact:
Re: Elsa Babe 160cm L-cup REVIEW
The doll seems to be repaired I will next put up photos the back after it has been sealed. The silicone glue I let stay 12 hours so those photos comes tomorrow or later.
Review of my Monica Hentai Torso Doll - viewtopic.php?t=169345
Review of my Elsa Babe 160cm L-cup - viewtopic.php?t=172708
Best way to clean a doll
Best way to dry a doll
Where to buy doll clothes
After honeymoon
Re: Elsa Babe 160cm L-cup REVIEW
Hanna: viewtopic.php?t=161099
Zhen: viewtopic.php?t=160371
Sam: viewtopic.php?t=160188
Lapis: viewtopic.php?p=2251699#p2251699
Lulu: viewtopic.php?t=141384
Selene: viewtopic.php?t=178008
- baphometric
- Moderator
- Posts: 858
- Joined: Wed Oct 14, 2020 7:08 pm
- Location: USA
- Contact:
Re: Elsa Babe 160cm L-cup REVIEW
- just a guy
- Doll Mentor
- Posts: 1040
- Joined: Tue Apr 25, 2023 3:36 pm
- Location: Finland
- Contact:
Re: Elsa Babe 160cm L-cup REVIEW
Review of my Monica Hentai Torso Doll - viewtopic.php?t=169345
Review of my Elsa Babe 160cm L-cup - viewtopic.php?t=172708
Best way to clean a doll
Best way to dry a doll
Where to buy doll clothes
After honeymoon
Re: Elsa Babe 160cm L-cup REVIEW
Elsa Babe 150cm Silicone & 160cm TPE - ZHB001, ZHB003, DHR003, XHC001.
YL head #193.
- just a guy
- Doll Mentor
- Posts: 1040
- Joined: Tue Apr 25, 2023 3:36 pm
- Location: Finland
- Contact:
Re: Elsa Babe 160cm L-cup REVIEW
I think the epoxy by itself just isn't strong enough since there is so much pressure on the back when bending it. I think the only solution is to drill hole and put prick through the back bone pipe and the nut it will take the biggest pressure and then also add epoxy. Like I said though the pipe is too tough to drill. I will test couple more time then have to think to get rid of the doll all together since it's useless as it is now if I can't fix it.
Review of my Monica Hentai Torso Doll - viewtopic.php?t=169345
Review of my Elsa Babe 160cm L-cup - viewtopic.php?t=172708
Best way to clean a doll
Best way to dry a doll
Where to buy doll clothes
After honeymoon
Re: Elsa Babe 160cm L-cup REVIEW
Hanna: viewtopic.php?t=161099
Zhen: viewtopic.php?t=160371
Sam: viewtopic.php?t=160188
Lapis: viewtopic.php?p=2251699#p2251699
Lulu: viewtopic.php?t=141384
Selene: viewtopic.php?t=178008
- DarkMind1982
- Senior Member
- Posts: 404
- Joined: Fri Jun 17, 2022 2:58 pm
- Location: Russia
- Contact:
Re: Elsa Babe 160cm L-cup REVIEW
For this i can only advise diamond coated drill and cut through slowly.
- just a guy
- Doll Mentor
- Posts: 1040
- Joined: Tue Apr 25, 2023 3:36 pm
- Location: Finland
- Contact:
Re: Elsa Babe 160cm L-cup REVIEW
Review of my Monica Hentai Torso Doll - viewtopic.php?t=169345
Review of my Elsa Babe 160cm L-cup - viewtopic.php?t=172708
Best way to clean a doll
Best way to dry a doll
Where to buy doll clothes
After honeymoon
Re: Elsa Babe 160cm L-cup REVIEW
just a guy:just a guy wrote: ↑Tue Apr 02, 2024 4:04 pm I don't hink the diamond srill helps since I can't put enough pressure on the pipe since on my other had I need to keep the silicone away of the drill and too much pressure the drill can esily slip. This has happened.
Did you try first making a dimple as was advised below? This is super important.
If I understood correctly, you are also having trouble drilling as you need your second hand to hold the silicone skin away from the skeleton. What would help with this is a cheap spreader clamp. In the absence of this, perhaps jerry-rigging a circular retracter would work. I don't know the amount of pressure required to keep the silicone spread apart as I don't have a doll (yet), but here's a suggestion to allow you to free up one of your hands to make the work easier:MinniMagg wrote: ↑Sat Mar 16, 2024 12:06 pm ...
Another key thing to Drilling into a piece of pipe is that you need a dimple or an indent in the pipe in order for the drill bit to Center into. Otherwise it will simply wander off the tube. The hardware store will have hardened Steel Center punches for this task.
...
Find a larger diameter circular plastic tub (say, a yogurt container or larger). Cut the top 4-5" (10-12cm) off and place that circular piece in the hole in the doll's back to keep the skin spread apart as you work "inside" it's diameter. This would free up one of your hands to more securely hold the pipe as you first punch a dimple into the metal, and later as you drill.
A large empty tomato can would work as well, but you'd need tin snips or similar to cut it's height down to use in the same way.
Re: Elsa Babe 160cm L-cup REVIEW
Elsa Babe 150cm Silicone & 160cm TPE - ZHB001, ZHB003, DHR003, XHC001.
YL head #193.
- just a guy
- Doll Mentor
- Posts: 1040
- Joined: Tue Apr 25, 2023 3:36 pm
- Location: Finland
- Contact:
Re: Elsa Babe 160cm L-cup REVIEW
I did made some sort of dimple yes. The silicone is very tough so the plastic cup has to be very sturdy.
Review of my Monica Hentai Torso Doll - viewtopic.php?t=169345
Review of my Elsa Babe 160cm L-cup - viewtopic.php?t=172708
Best way to clean a doll
Best way to dry a doll
Where to buy doll clothes
After honeymoon
- just a guy
- Doll Mentor
- Posts: 1040
- Joined: Tue Apr 25, 2023 3:36 pm
- Location: Finland
- Contact:
Re: Elsa Babe 160cm L-cup REVIEW
Review of my Monica Hentai Torso Doll - viewtopic.php?t=169345
Review of my Elsa Babe 160cm L-cup - viewtopic.php?t=172708
Best way to clean a doll
Best way to dry a doll
Where to buy doll clothes
After honeymoon