Head connector type

davenma · Post by **davenma** » Sun Apr 28, 2024 2:36 pm

Don't see it mentioned in specs on your vendor site: what is head connector type for your heads/neck interface. Want to determine compatibility with other mfg heads. Thx.

Treepusher · Post by **Treepusher** » Sun Apr 28, 2024 5:51 pm

My Jiusheng has the M16 bolt, pretty much the standard.

Post by **SxDolled** » Sun Apr 28, 2024 7:14 pm

Jiusheng utilises the M16 bolt like most

Post by **jiusheng-doll** » Mon Apr 29, 2024 10:09 pm

M16, three connector types to choose.

seagull · Post by **seagull** » Tue Apr 30, 2024 3:03 am

Emma

ondsdoll · Post by **ondsdoll** » Tue Apr 30, 2024 7:47 am

jiusheng-doll wrote: ↑Mon Apr 29, 2024 10:09 pm M16, three connector types to choose.

1 is best, head will be on and stays on.

jeep2639 · Post by **jeep2639** » Tue Apr 30, 2024 8:26 am

ondsdoll wrote: ↑Tue Apr 30, 2024 7:47 am
jiusheng-doll wrote: ↑Mon Apr 29, 2024 10:09 pm M16, three connector types to choose.
1 is best, head will be on and stays on.

It depends on how you use/store the doll. If the head can stay on all the time, then #1 might be right for you. If the head has to come off frequently (for storage or for changing heads who share the same body) then you may want #2. #3 gives some extra head motion.

ondsdoll · Post by **ondsdoll** » Tue Apr 30, 2024 9:07 am

jeep2639 wrote: ↑Tue Apr 30, 2024 8:26 am
ondsdoll wrote: ↑Tue Apr 30, 2024 7:47 am
jiusheng-doll wrote: ↑Mon Apr 29, 2024 10:09 pm M16, three connector types to choose.
1 is best, head will be on and stays on.
It depends on how you use/store the doll. If the head can stay on all the time, then #1 might be right for you. If the head has to come off frequently (for storage or for changing heads who share the same body) then you may want #2. #3 gives some extra head motion.

That's true, but I have my dolls in bed with me and a head falling off (during sex) can be an expensive problem.

jeep2639 · Post by **jeep2639** » Tue Apr 30, 2024 10:51 am

I never had the problem of the head falling off. Note one thing. Those connectors have little balls, behind them a spring, and behind it a small Allen screw. There are two of those. Your screws (the adapter's screws... not yours...) might be a little loose. Take the Allen screwdriver that came with it (or one that fits) and tighten a little bit. Did you try that? I never had a head even indicating it wants to come off... In the right picture from Jiusheng you can see one of the balls and one of the Allen screws.

Star88 · Post by **Star88** » Tue Apr 30, 2024 12:09 pm

With the quick release connectors, does it matter weather the threaded end goes on the body or the head? My two new heads each came with one and it would seem to make more sense to thread into head, and "plug" into neck.

jeep2639 · Post by **jeep2639** » Tue Apr 30, 2024 4:01 pm

Star88 wrote: ↑Tue Apr 30, 2024 12:09 pm With the quick release connectors, does it matter weather the threaded end goes on the body or the head? My two new heads each came with one and it would seem to make more sense to thread into head, and "plug" into neck.

The advantage in screwing into the body is that you can use one for many heads… my problem is that one of the heads I have has the adapter screwed so hard into the head that I can’t take it out, and I’m afraid to ruin the head if I tried too hard. Both ways work.

Davey2469 · Post by **Davey2469** » Tue Apr 30, 2024 4:23 pm

davenma wrote: ↑Sun Apr 28, 2024 2:36 pm Don't see it mentioned in specs on your vendor site: what is head connector type for your heads/neck interface. Want to determine compatibility with other mfg heads. Thx.

My preference is #3 also noting that Irontech has the neck silicon farther up (or to say the threads are recessed) than my Starpery and using it in the head actually allows for more head movement. I did add a brass washer under the ball bearing.