Purposely removing the TPE from a doll I don't want
- hardwiguy
- Active Member
- Posts: 185
- Joined: Mon Dec 19, 2022 3:24 pm
- Location: California, USA
- Contact:
Purposely removing the TPE from a doll I don't want
So, this post is sort of in the opposite spirit of this particular board, and I want to apologize in advance for that! I have done some searching and some reading about this already, but there is surprisingly little that I can find in terms of what I want to do.
I made a different thread about my silicone Tayu doll, Hoshi. This time, however, I'm writing about a poorly made TPE doll that I don't want anymore. I don't feel comfortable selling it or giving it away, so I'm left with the unenviable task of trying to "disassemble" it. The trouble is, I had no idea how labor-intensive it would be to remove TPE! I've been using an Exacto knife so far, but seeing as though the TPE is extremely thick in the trunk of her body (and thighs/butt especially), I've only been able to remove a tiny portion thus far.
Without using chemicals (since I'm doing this in my apartment's spare bedroom), I wonder if anyone has suggestions to speed this process up a bit. I have had to do 15-20 passes with the knife just to fully cut through the TPE on her feet!
I have a feeling that doing this to a silicone doll would be much easier. However, it is what it is, and any tools suggestions (or other suggestions) would be greatly appreciated!
Thanks in advance.
Re: Purposely removing the TPE from a doll I don't want
hardwiguy wrote: ↑Thu Mar 07, 2024 6:54 pm Hey again folks,
So, this post is sort of in the opposite spirit of this particular board, and I want to apologize in advance for that! I have done some searching and some reading about this already, but there is surprisingly little that I can find in terms of what I want to do.
I made a different thread about my silicone Tayu doll, Hoshi. This time, however, I'm writing about a poorly made TPE doll that I don't want anymore. I don't feel comfortable selling it or giving it away, so I'm left with the unenviable task of trying to "disassemble" it. The trouble is, I had no idea how labor-intensive it would be to remove TPE! I've been using an Exacto knife so far, but seeing as though the TPE is extremely thick in the trunk of her body (and thighs/butt especially), I've only been able to remove a tiny portion thus far.
Without using chemicals (since I'm doing this in my apartment's spare bedroom), I wonder if anyone has suggestions to speed this process up a bit. I have had to do 15-20 passes with the knife just to fully cut through the TPE on her feet!
I have a feeling that doing this to a silicone doll would be much easier. However, it is what it is, and any tools suggestions (or other suggestions) would be greatly appreciated!
Thanks in advance.
Hi there,
I have been in the same boat twice, and have havested TPE from two dolls (one with a foam core).
My advice would be to get a sharp pair of kitchen/garden shears/scissors. Scissors will make short work to TPE. A knife has one cutting edge, and with TPE being such a flexible material, I don't think the blade "bites" into the material, hence your difficulty.
Just make a small snip with the point of your new super sharp scissors, and continue to expand the cut. Or find a spot on your doll that exposes the internal skeleton (either the neck connector, or the foot bolts (if your doll has the standing bolt feature)) and start from there. If your scissor is sharp though it won't be a problem.
My foam core was a bit more challenging (I just had to cut off the TPE from the foam core since the core was pretty hard).
https://www.homedepot.ca/product/fiskar ... 1001181471
something like this with a spring will also reduce the stress on your hands.
I have held on to the TPE that I have harvested, and it has come in super handy for repairs, or sealing holes! If you get some 3M 94 Tape Primer you can make your own TPE paste so remember to save some for future repairs, I think even low quality TPE could be useful.
Hope this helps!
- baphometric
- Moderator
- Posts: 837
- Joined: Wed Oct 14, 2020 7:08 pm
- Location: USA
- Contact:
Re: Purposely removing the TPE from a doll I don't want
Re: Purposely removing the TPE from a doll I don't want
Jael - (YL 148) viewtopic.php?f=212&t=73333
Miriame - (SM 136) viewtopic.php?f=269&t=102115
Beth - (SM 157G) viewtopic.php?f=269&t=149637
Brooke - (Starpery 148F) viewtopic.php?t=175783
***
- H_N_Franku
- Active Member
- Posts: 103
- Joined: Wed Feb 14, 2024 1:04 pm
- Contact:
Re: Purposely removing the TPE from a doll I don't want
- The Doll Advocate
- Doll Mentor
- Posts: 1582
- Joined: Wed Nov 23, 2022 8:30 pm
- Location: Texas
- Contact:
Re: Purposely removing the TPE from a doll I don't want
Re: Purposely removing the TPE from a doll I don't want
Yes, if you do so though put a chemical mask on and do it in a well ventilated area. TPE fumes are toxic as HELL.The Doll Advocate wrote: ↑Thu Mar 07, 2024 8:17 pm I use a hot knife ,it will slice through just like butter and they are cheap to buy about 20$.
Jael - (YL 148) viewtopic.php?f=212&t=73333
Miriame - (SM 136) viewtopic.php?f=269&t=102115
Beth - (SM 157G) viewtopic.php?f=269&t=149637
Brooke - (Starpery 148F) viewtopic.php?t=175783
***
- hardwiguy
- Active Member
- Posts: 185
- Joined: Mon Dec 19, 2022 3:24 pm
- Location: California, USA
- Contact:
Re: Purposely removing the TPE from a doll I don't want
Hot knife sounds like a bad idea for me in my situation, where I don't have any good way to ventilate my "work room" properly. Good idea overall though!The Doll Advocate wrote: ↑Thu Mar 07, 2024 8:17 pm I use a hot knife ,it will slice through just like butter and they are cheap to buy about 20$.
- hardwiguy
- Active Member
- Posts: 185
- Joined: Mon Dec 19, 2022 3:24 pm
- Location: California, USA
- Contact:
Re: Purposely removing the TPE from a doll I don't want
That definitely helps, thanks. I was about to try one of my scissors, but realized they aren't pointy enough to really get it started. Pruning scissors are a great idea, I'll order a pair. Thanks!magnussam wrote: ↑Thu Mar 07, 2024 7:10 pmhardwiguy wrote: ↑Thu Mar 07, 2024 6:54 pm Hey again folks,
So, this post is sort of in the opposite spirit of this particular board, and I want to apologize in advance for that! I have done some searching and some reading about this already, but there is surprisingly little that I can find in terms of what I want to do.
I made a different thread about my silicone Tayu doll, Hoshi. This time, however, I'm writing about a poorly made TPE doll that I don't want anymore. I don't feel comfortable selling it or giving it away, so I'm left with the unenviable task of trying to "disassemble" it. The trouble is, I had no idea how labor-intensive it would be to remove TPE! I've been using an Exacto knife so far, but seeing as though the TPE is extremely thick in the trunk of her body (and thighs/butt especially), I've only been able to remove a tiny portion thus far.
Without using chemicals (since I'm doing this in my apartment's spare bedroom), I wonder if anyone has suggestions to speed this process up a bit. I have had to do 15-20 passes with the knife just to fully cut through the TPE on her feet!
I have a feeling that doing this to a silicone doll would be much easier. However, it is what it is, and any tools suggestions (or other suggestions) would be greatly appreciated!
Thanks in advance.
Hi there,
I have been in the same boat twice, and have havested TPE from two dolls (one with a foam core).
My advice would be to get a sharp pair of kitchen/garden shears/scissors. Scissors will make short work to TPE. A knife has one cutting edge, and with TPE being such a flexible material, I don't think the blade "bites" into the material, hence your difficulty.
Just make a small snip with the point of your new super sharp scissors, and continue to expand the cut. Or find a spot on your doll that exposes the internal skeleton (either the neck connector, or the foot bolts (if your doll has the standing bolt feature)) and start from there. If your scissor is sharp though it won't be a problem.
My foam core was a bit more challenging (I just had to cut off the TPE from the foam core since the core was pretty hard).
https://www.homedepot.ca/product/fiskar ... 1001181471
something like this with a spring will also reduce the stress on your hands.
I have held on to the TPE that I have harvested, and it has come in super handy for repairs, or sealing holes! If you get some 3M 94 Tape Primer you can make your own TPE paste so remember to save some for future repairs, I think even low quality TPE could be useful.
Hope this helps!