Forum Rules,TOS and Privacy Policy | By visiting this website and viewing the pages within, you accept and agree to be bound by and comply with our Rules Of Conduct, Terms Of Use and Privacy Policy
Before using sharp instruments - on an inflata-babe
See if you can just gently rub the insert - starting at the edge and gently using the rubbing motion to pull off the insert - working around the entire insert -
Yes, that's good advice, and Capt Yorkie is right. I thought about it after I posted, and then realised that it probably wasn't the best advice, so I modified my words slightly. If I recall, I think that I just tugged at the insert gently until it finally came loose. I wasn't as lucky as many here, and the insert in my doll showed no signs of coming loose on its own.
erf72 wrote:I agree the inserts do look good but if I want some extra fun with her I need to replace them as they are to small, I'm just a bit concerned I'll damage her pulling them out. Did you notice if there was glue around the top edge only or all the way down when yours came out?
Hi erf72. They are only glued at the top, not all the way down. You might have to use a razor knife and be real careful. I managed to remove the stock insert from my Agent 69 without damaging her. The problem with these particular dolls is that the insert is not designed to be removed because there is a vinyl lip that the insert glues to at the surface. As a result what happens is that this lip will split from continually removing and reinserting the insert, and can tear into the inner vinyl chamber if it goes too far. Ideally you would take a spare piece of vinyl and reinforce this area to prevent the tearing.
I know what you mean about how incredibly tight these dolls are. That being said, I was able to successfully use my Agent 69 in her stock configuration with a viagra hard on, plenty of lube, and a will to succeed It really helps to deflate her down quite a bit first, since the more that she's aired up, the tighter she is.
Sam
I had all the will in the world but no viagra, guess that was the problem Anyway I think I'm going to have to change it as it just wasn't happening, it's interesting that you mentioned that vinyl lip because I was wondering if you could use her without any inserts at all, a bit like the cheap inflata-babes (is that what she looks like without an insert?) anyway now you've mentioned that lip I have my doubts, it sounds like it might be painful.
Before using sharp instruments - on an inflata-babe
See if you can just gently rub the insert - starting at the edge and gently using the rubbing motion to pull off the insert - working around the entire insert -
The two NMC air babes I had {Natalie & Cayenne} purchased a few years ago were done that way - although - they showed signs of coming undone just from normal routine usage - but to get the remainder of the insert off - that's the trick I used
She is just such a fine air babe - do note though - as the insert is used more and more - the better it gets - sure is tight in the beginning - but that does loosen up
Thanks for the advice yorktown, I'll give that technique a try, I have previously read she loosens up after some use but the problem is I can't even get that far
erf72 wrote: it's interesting that you mentioned that vinyl lip because I was wondering if you could use her without any inserts at all, a bit like the cheap inflata-babes (is that what she looks like without an insert?) anyway now you've mentioned that lip I have my doubts, it sounds like it might be painful.
I've heard of people actually using these dolls that way erf72, and with good success. It's probably the removal and insertion of the inserts that causes the outer lip to split mostly. Still, it would probably be a good idea to reinforce this area none the less. You might be able to get away with using the VLP Vinyl repair by laying a thick bead around the perimeter of the area in question.
As to whether or not it would be a comfortable experience, I can't say as I've never tried a doll this way. But her orifice would probably be just about right without the insert. Even when I installed an after market insert, I still had to deflate my doll down significantly in order to enter her with ease.
I am glad to see such a renewed interest in these dolls, as expressed recently in this thread and in other threads recently started. I'd like to share on here the "creepy" photo I entered in this month's photo contest. The caption is "It's OK to grab DOLLS by the pussy!" Anyone interested can vote here: http://www.dollforum.com/forum/viewtopi ... 19&t=77568 by logging into TDF and clicking the box next to the photos you want to vote for.
I was wondering from the people who own a Cayenne how robust is she? As in how much can she take without blowing a seam. Not that I plan on going wild or anything but I am on a tight budget and want something that will last.
I was wondering from the people who own a Cayenne how robust is she? As in how much can she take without blowing a seam. Not that I plan on going wild or anything but I am on a tight budget and want something that will last.
Also I plan on repainting her face and make up
Although it was the best blow up doll, it was broken the first time after about 5 time use and the second was broken de second time of use. Im done with blow up dolls, Most inflatables have bad inserts and the few that have a good insert are broken after a few times.
Thank you for your response. Still leaning towards getting one. I suppose I am not fussed about the inserts because I'm a girl. It's just for now they are a cheaper alternative then the silicon variety
hi, how do you guys clean Cayenne's pussy? It looks like it cannot be removed from the body and I've not find a way how to push thru a long pussy-anus sleeve.
How to pour water into one hole and let it run out through the other?
I used a plastic stick that once for transport when delivering an insert (bestsexdoll) and around it I wrap a handkerchief then push in the insert, then rewind with a new handkerchief. Still remains working and worked.
bonestaak wrote:I used a plastic stick that once for transport when delivering an insert (bestsexdoll) and around it I wrap a handkerchief then push in the insert, then rewind with a new handkerchief. Still remains working and worked.
I wonder how company can make a product which is so difficult to clean and also without instructions.
Any other tips from you guys how you deal with it?