heartbroken

curious dave · Post by **curious dave** » Mon Jul 03, 2017 9:26 pm

i have had my doll 160 4 months fixed vagina very bad idea it was my first doll the vagina has tore so much glue wont fix it i bought the glue from vendor its just a big massive hole now when legs are open im unable to use for sex. question is and its pretty much a call for help as she cost so much money i dont wanna throw her away and im unable to afford another one. with having a fixed vagina do you think its possible to somehow make the hole able to take a different sort of pussy like a fleshlight or something i dont know how i would start to be able to mod that way. has this happend before and ended with success or do i just accept that shes ruined forever. any help or ideas would be great thank you

bob7892 · Post by **bob7892** » Mon Jul 03, 2017 9:58 pm

Need more information , who was the doll made by what material is it , can you post a picture of thee damaged area .
It is possible to sculpt out a hole to take a insert but the repair will look a bit Frankenstein ish , if the hole is bigger than a insert it's toast .
How on earth did you manage to get it into that state in 4 months

carlys_guy · Post by **carlys_guy** » Mon Jul 03, 2017 10:03 pm

contact samara78 she is good at doing repairs.

carlys_guy

curious dave · Post by **curious dave** » Mon Jul 03, 2017 11:14 pm

i will post pic in morning its a wm doll 160 tpe. i think it was with cleaning her never really thought it would tear its all my own fault so this is my doing by not been careful what i can remember doing is putting a gel silica pouch it and i could not get it out so stupid me put my whole hand in. i bought the proper glue fixed it twice its just no good shes now in spare room i wont go near her its got me sick to the stomach as i saved up a long time for her i knew from the start it wasn't easy cos shes really heavy but stupid me said o it will be easy.think this is the most costly mistake ive made.

curious dave · Post by **curious dave** » Mon Jul 03, 2017 11:43 pm

Mark Spencer · Post by **Mark Spencer** » Tue Jul 04, 2017 12:07 am

did she just give birth?

.. to a hippopottamus?

Is that a WM type? or is it actually from WM?

curious dave · Post by **curious dave** » Tue Jul 04, 2017 12:25 am

from wm

Tybalt · Post by **Tybalt** » Tue Jul 04, 2017 12:34 am

You have to do multiple layers. Apply thin layer of tpe glue and close legs to press pussy together. Wait like 4-8 hours to fully cure. Apply another thin layer of tpe glue. Close legs and let cure for 4-8 hours.

Mark Spencer · Post by **Mark Spencer** » Tue Jul 04, 2017 12:39 am

Have they given you any advice on it? Or have they seen these pics?
That looks like a time consuming repair, maybe best done in several stages.

jm6o8u · Post by **jm6o8u** » Tue Jul 04, 2017 12:40 am

I have never own a TPA doll.

That is fixable .
I read where thy where using a hot spoon to fix tars .
Need to do it in well vent room TPA gives off nauseous gas when malted.
A little at a time.
She will be back good as new.

ZannyDanger · Post by **ZannyDanger** » Tue Jul 04, 2017 12:40 am

Damn, that's some serious damage... hope you can get it fixed

Ive read somewhere around here about using a soldering iron and some of the test tpe to melt it together... maybe that could work.

curious dave · Post by **curious dave** » Tue Jul 04, 2017 12:47 am

more detail

curious dave · Post by **curious dave** » Tue Jul 04, 2017 12:48 am

so as you can see its top and bottom where the tear is

Mark Spencer · Post by **Mark Spencer** » Tue Jul 04, 2017 12:52 am

Yep. It *can* be repaired, but it will require some patience and
some time. I'd start with a good cleaning, oil and then start at the
innermost portion of the tear, work on a small portion and move
outward. A little on the top, a little on the bottom, let it rest and
then do it again till you reach the outside.
The repaired area is never quite the same, but it is something you can fix.