Repairing/Enlarging TPE breasts

CF · Post by CF » Wed Nov 02, 2016 7:47 pm

seedlessRaisins, I don't think it's possible.

seedlessRaisins · Post by **seedlessRaisins** » Thu Nov 03, 2016 4:22 pm

yeh I thought so. I may create post to see what thoughts are out there.
But I expect little. I feel that any "operation" wouldn't be a amature job.

astroman440 · Post by **astroman440** » Sat Nov 12, 2016 3:29 am

I did an experiment with an OR doll torso a few day ago. Because the TPE breaths, I bought 36 inch balloons on amazon, made a small hole on the side of the breasts and stuffed the balloon into the hollow area, leaving the part you blow into sticking out. Then I put the balloon around a bathtub faucet nd filled them up with water. Not to 36 inches obviously haha. I thought bigger balloons would make the end result softer and that the water would cause a natural sag but the the was stretched tightly enough that they were pretty firm once the balloons were tied. The hole wasn't all that big in the end. Since they were so firm, I decided to reverse the process after ehem, testing them out.

I didn't get any pics, sorry, and I'm not planning to do it again but those were my experiences.

CF · Post by CF » Mon Nov 14, 2016 1:22 am

astroman440, if you DO repeat the process, photos would be very interesting and appreciated!

abracadabra · Post by **abracadabra** » Sat Nov 26, 2016 11:16 am

seedlessRaisins wrote:Is it possible to do the reverse on a WM A cup doll, and make the breasts smaller?
Will these be filled with air?
They seem very solid, so not sure.

I would think material would have to be removed to reduce size. And will most likely leave scars.

abracadabra · Post by **abracadabra** » Sat Nov 26, 2016 12:33 pm

Breast augmentation so far so good

CF · Post by CF » Sat Nov 26, 2016 1:35 pm

WOW, WOW, WOW! To confirm, this is the ORDoll torso that you have pictured? Can you please post some more photos including shots of where you inserted the balloons? That will help us to replicate the process.

This looks FANTASTIC! Thank you for sharing. Looking forward to seeing more of your progress!

abracadabra · Post by **abracadabra** » Sat Nov 26, 2016 2:12 pm

CF wrote:WOW, WOW, WOW! To confirm, this is the ORDoll torso that you have pictured? Can you please post some more photos including shots of where you inserted the balloons? That will help us to replicate the process.

This looks FANTASTIC! Thank you for sharing. Looking forward to seeing more of your progress!

THIS IS NOT MY OR DOLL TO BE CLEAR.
It's my 148 with questionable origin.
This is very much in the experimental stage and as to not spread misinformation that could potentially tear up others dolls, I am going to refrain from my process until I'm satisfied that it works.
I just thought I would show some early results, because at least at this point I'd rather satisfied. However it's too early for me to say for sure

CF · Post by CF » Sat Nov 26, 2016 2:38 pm

It looks really great. Such an improvement in both size and shape.

Best of luck, and keep us all posted!

stones · Post by **stones** » Sat Nov 26, 2016 3:57 pm

That looks great abracadabra, a YL148 with bigger breasts would be a great option!

abracadabra · Post by **abracadabra** » Sat Nov 26, 2016 4:39 pm

CF wrote:It looks really great. Such an improvement in both size and shape.

Best of luck, and keep us all posted!

Thank you I'm hoping that the end result has a slightly saggy more natural look and it should if all goes well

samara78 · Post by **samara78** » Sat Nov 26, 2016 9:22 pm

enlarging is by injection of air. The doll will soak up any vasiline or petrolium jelly.

A cup is already pretty small don't you think?

abracadabra · Post by **abracadabra** » Sat Nov 26, 2016 10:20 pm

[quote="samara78"]enlarging is by injection of air. The doll will soak up any vasiline or petrolium jelly. [quote]

the problem I have had with air injections is they seem to leak out somewhere inside , especially if the enlargement is several cup sizes. a deflated breast is no biggie.
but in time once I'm sure it works, and I'm sure it will, hopefully have a method for breast augmentations that doesn't depend on air pressure or fillers.
on a small scale test it works. hopefully by tomorrow evening I will have some results..

bigbadplaid · Post by **bigbadplaid** » Mon Nov 28, 2016 2:15 pm

With the balloons, was their any special tools or technique needed to make the holes? I want to try the balloons on a silicon torso, yet I'm worried I'll just cause too much damage to her