Ask the docs.

samara78 · Post by **samara78** » Wed Dec 14, 2016 7:26 am

Booty Call Dolls wrote:Samara78,
Any tips on more tips on make ups to pass on?
should oil based be avoided?
Jeff and Nyoko

Anything fatty or with fats in it may be bad.

samara78 · Post by **samara78** » Wed Dec 14, 2016 7:29 am

abracadabra wrote:In regards to Heating if you do not have an electric blanket it's not so difficult to remove the head place a garbage bag over body place in shower and turn on hot water and run for a few minutes remove bag, body also warm

Warm water is better. Too hot and deformation could occur.
Depending on the doll 75°-99° can disfigure a doll depending on the blend of material.

Sarg · Post by **Sarg** » Mon Dec 26, 2016 5:01 pm

Just got my YL Doll, 148 d cups, with an OR head and an WM head (OR-001 and WM- 74). Arrived Christmas Eve day from Beautiful Dolls. I will do a review after several days of getting to know her and selecting the appropriate photos for posting. Briefly, Joy at BD did a great job of keeping up with my changes to the order and quickly getting my doll and produced and shipped. Very pleased.

But here is my question for the Docs. I went wth the built-in VJ rather than removable for aesthetics. I did read the pros and cons of both, so I didn't do it without consideration. I find the VJ is very well constructed to look real. Very nice as is the doll and 2 heads as a whole. But the problem is the entry hole is too small and tight for me to penetrate, even with a shot of viagra. So, my question: Is it safe to enlarge the hole by careful cutting it? Or does that invite trouble (rips or further tearing, like pulling a loose thread that unravels more). Also, would inserting a wide dildo shaped object to streatch her out work as an alternative to surgery? Your thoughts from your experiences and knowledge would be much appreciatd.

samara78 · Post by **samara78** » Mon Dec 26, 2016 9:35 pm

This one is a sensitive issue. With mutiple choices.
I will think about this onefor a short while and get back to tomorrow

Post by **Booty Call Dolls** » Mon Dec 26, 2016 9:55 pm

samara78,
That one is a tough one because if she is not large enough inside, will cutting the outside even make a difference?
Sarg,
Alot of people think built in looks so much nicer until they see below taken by a BCD Family member who is proud owner of a YL 155.
Best,
Jeff

Anung Un Rama · Post by **Anung Un Rama** » Mon Dec 26, 2016 10:50 pm

Sarg wrote: So, my question: Is it safe to enlarge the hole by careful cutting it? Or does that invite trouble (rips or further tearing, like pulling a loose thread that unravels more). Also, would inserting a wide dildo shaped object to streatch her out work as an alternative to surgery? Your thoughts from your experiences and knowledge would be much appreciatd.

Hi Sarg...if you go this method ensure the material the "dildo" is made from is TPE compatable or compatable with the material of you doll's flesh.

This prevents chemical reaction and potential meltdown and distortion of the doll or the insertables materials. For example do not use a silicone dildo on a tpe doll and vice versa.

Cheers Anung

samara78 · Post by **samara78** » Mon Dec 26, 2016 11:25 pm

Try streching her a warmed and smooth glass dildo.
Have it warmed in a 102 degrees water(no warmer then that) i warn you now. Meanwhile put gloves into petroleum jelly and apply to inside of vagina. Insert said warm glass dildo with some petroleum jelly, insert slowly into the doll holding her "lips" open insert the dildo with the other hand. (quick trick make sure to change gloves, and cleaning the petroleum from the "lipv area will make this part a breeze. Never used this method on any dolls i have had, that are tpe, this method is less invasive and may stretch her out over 2 maybe 3 days. I wished the best of luck.

samara78 · Post by **samara78** » Mon Dec 26, 2016 11:27 pm

Booty Call Dolls wrote:samara78,
That one is a tough one because if she is not large enough inside, will cutting the outside even make a difference?
Sarg,
Alot of people think built in looks so much nicer until they see below taken by a BCD Family member who is proud owner of a YL 155.
Best,
Jeff

This is the insert version? Her lady bits are very realistic.

skyhawk747 · Post by **skyhawk747** » Tue Dec 27, 2016 1:12 pm

Booty Call Dolls wrote:Alot of people think built in looks so much nicer until they see below taken by a BCD Family member who is proud owner of a YL 155.
Best,
Jeff

Im confused? Jeff so the 2 pictures are inserts and not a build in Vag?

samara78 · Post by **samara78** » Tue Dec 27, 2016 1:37 pm

skyhawk747 wrote:
Booty Call Dolls wrote:Alot of people think built in looks so much nicer until they see below taken by a BCD Family member who is proud owner of a YL 155.
Best,
Jeff
Im confused? Jeff so the 2 pictures are inserts and not a build in Vag?

That definitely is an insert version of the doll.

skyhawk747 · Post by **skyhawk747** » Tue Dec 27, 2016 1:47 pm

Thanks Samara,

Jeff sent me this pic in an email yesterday and I assumed it was fixed as it svery hard to see that as an insert.

Is it possible to see a built in vagi pic so we can compare?

Cheers

samara78 · Post by **samara78** » Tue Dec 27, 2016 8:07 pm

They look the same unless you really really spread the legs. With legs shut they look the same.

Post by **Booty Call Dolls** » Wed Dec 28, 2016 12:13 am

Jeff sends those to most people to show that insert can look good too.
Love,
Nyoko

samara78 · Post by **samara78** » Wed Dec 28, 2016 12:32 am

Thank you ms Nyoko.

Sarg · Post by **Sarg** » Wed Dec 28, 2016 12:56 am

Jeff, thanks for the quick response. It seems the outer hole entrance is about one inch deep, and then you're into an expanded area. So I wondered if sculpting out the hole to make it wider would work so I can get past that first inch. But, since I'm not familiar with all the properties of TPE I don't know if a "slice" might invite that area to tear further.

I also like the idea of the heated glass dildo. Also, guys, thanks for the caution on compatibility of materials.

As a note, I have an older silicone doll where there is no problem of entry. But this new combo of the YL 148 and the OR and WM heads is fantastic. And the TPE material is miles better than the high grade platinum silicone of just 4 years ago. I was not let down by this new purchase.

Thanks to all for your comments.