SKYLAR Sleepy and Sexy DS 163 #silicone repairs made easy

Ddwyerstar · Post by **Ddwyerstar** » Mon Nov 27, 2017 5:55 pm

After a break, Skylar stretches out and relaxes!

von_Shredhead · Post by **von_Shredhead** » Sun Mar 11, 2018 9:17 pm

Hey Ddwyerstar!
Great repairs and thanks for the instructions and links to the products you used. This will be very helpful in the near future.

Skylar in Pink ... AWESOME!!! I can only imagine fighting temptation while doing the photo shoot ... I'd lose too!

Cheers!
Von

Hungry Bear · Post by **Hungry Bear** » Sun Mar 11, 2018 10:52 pm

Great work! Too bad there aren't materials to repair TPE as well!

Kazuya · Post by **Kazuya** » Mon Mar 12, 2018 6:37 am

Loving the pink wig. Very sexy. Did you need an adapter for the WM and OR heads?

Up2myneck · Post by **Up2myneck** » Mon Mar 12, 2018 7:26 am

Hi Ddwyerstar,

That is one very sexy looking doll lady!

I really would..............

Looking forward to seeing more of her!!

VegasBill · Post by **VegasBill** » Mon Mar 12, 2018 5:20 pm

Great photos, she's gorgeous and very sexy poses.... great stuff

Post by **mi6c** » Tue Mar 13, 2018 2:07 am

Kazuya wrote:Loving the pink wig. Very sexy. Did you need an adapter for the WM and OR heads?

He made the adaption himself as can be found here:
https://www.dollforum.com/forum/viewtop ... 43&t=74208

You can get an adapter to put M16 thread heads( WM, OR, ...) onto a DS body from DollStudio, however this is one of the very few adapters where fitting may not be without problems.
I suggest you read the post in the link above as it mentions some issues.
Basically on most M16 heads the thread depth into the head is too shallow to accommodate the DS mounting spire so you have too options to deal with that:
a) keep the head intact and accept a certain amount of spacing between the bottom of the head and top of the neck on the order of an inch/2-3cm which may or may not show as a gap
b) carefully destroy/remove the fiberglass bottom of the threading to allow for the spire thereby most likely also impairing any oral use of the head.
Note that I have seen heads that had an "open" threading into the head already but only rarely, those would always work.

I hope this helps.

Kind regards.

Kazuya · Post by **Kazuya** » Tue Mar 13, 2018 2:32 am

mi6c wrote:
Kazuya wrote:Loving the pink wig. Very sexy. Did you need an adapter for the WM and OR heads?
He made the adaption himself as can be found here:
https://www.dollforum.com/forum/viewtop ... 43&t=74208

You can get an adapter to put M16 thread heads( WM, OR, ...) onto a DS body from DollStudio, however this is one of the very few adapters where fitting may not be without problems.
I suggest you read the post in the link above as it mentions some issues.
Basically on most M16 heads the thread depth into the head is too shallow to accommodate the DS mounting spire so you have too options to deal with that:
a) keep the head intact and accept a certain amount of spacing between the bottom of the head and top of the neck on the order of an inch/2-3cm which may or may not show as a gap
b) carefully destroy/remove the fiberglass bottom of the threading to allow for the spire thereby most likely also impairing any oral use of the head.
Note that I have seen heads that had an "open" threading into the head already but only rarely, those would always work.

I hope this helps.

Kind regards.

Thank you MI6c for your comprehensive response.