Ex-lite doll repair thread

[samara78]

The latex cures harder.

[mi6c]

The skin is not vinyl. Though vlp worked to seal a crack at the corner of her mouth.

Uhm, what worked ? vlp ?
Maybe I didn't pay enough attention or haven't had enough tea yet this morning, but kindly explain again what worked, please.

All the best.

[piacere]

maybe samara ment tlp? tender loving care

later lovers

[samara78]

VLP vinyl leather repair kit. This stuff disintegrates on the torso peice, and i will not be using it on the arms and legs. A miniscule amount on a toothpick was used on the corner of her mouth, i had a feeling had i used more. I would have melted her face.

[samara78]

I know everyone has been waiting for repaired pics. Here they are. Still have a couple of pieces on the inside to fix up.

[piacere]

Good good
and nice dress

later lovers.

[samara78]

Thank you so much. There is still much to do with her. I have to finish inside of the canal with more Latex. Once that is finished i will be very happy with the results.
These areas circled in red still need fixing up

[haremlover]

I've found the best glue to use is two part (2+1 ratio) expanding polyurethane foam itself. It's hideously sticky, sticks the foam to the foam well, sticks the foam to the plastic skeleton, and sticks one's paws together for days.

Best wishes

Harem

[samara78]

I've found the best glue to use is two part (2+1 ratio) expanding polyurethane foam itself. It's hideously sticky, sticks the foam to the foam well, sticks the foam to the plastic skeleton, and sticks one's paws together for days.

Best wishes

Harem

Lmao. The latex did it for me. Her vag will be good and strong. I can "grab her by the pussy" "i can do anything"
And she hasn't re opened whatsoever. Lol
Two part is not my thing.
Knowing how latex loves foam helped quite a bit in my decision. Please post your results for our benifit harem. Thank you so much.

[hopefull]

The latex did it for me.

Hi, I am in the midst of a major adaption to the Ex lite. Making the legs capable of splaying wider apart. I have cut the legs off so I can adapt the hip connector that stops the legs going any wider and have cut the legs so their natural orientation will be splayed, I have also cut down the leg bone (plastic tube) so the connector can be re-added.

I want to reattach the legs and was wondering if the Liquid latex is still holding up? could any liquid latex work do you think? or would I need the brand you used?

The outcome should be that rather than needing to stretch the doll for open legs, the inner thighs would compress for closed legs, thus stopping the dolls vaginina splitting

Regards Hopefull.

[hopefull]

PS. To explain better, my project.



1:- 1 shows the hip connector, this has a lip to stop the legs opening a very limited amount.

3:- shows the part of the leg removed.

4:- shows the part of the leg bone (plastic tube) to be cut down.

6:- shows the connector that will be reattached the the leg bone when cut down. It is simple as the connector just has a screw to tighten up against the leg bone.

Regards Hopefull.

[haremlover]

http://www.mbfg.co.uk/foam-materials.html is a useful source of soft foam

Best wishes

Harem

[hopefull]

http://www.mbfg.co.uk/foam-materials.html is a useful source of soft foam

Best wishes

Harem

Thanks Harem. will look into it

Regards Hopefull.

[samara78]

The latex holds up well,but leaves a hard feeling which i needed by the way.

[hopefull]

The latex holds up well,but leaves a hard feeling which i needed by the way.

Thanks, that sounds good

Regards Hopefull.